1. Unwind air shaft is controlled by powder brake
2. Rewind air shaft is controlled by torque motor
3. Each unwind has EPC device to prevent the material from moving left or right.
4. Oven 7.5meter, open and close is manual
5. Gluing with anilox roller which is shaftless installation
6. Manual doctor blade
7. Lamination part is controlled by inverter motor,lamination roller is heated by heat-conducted oil
Model |
YWGF800A |
YWGF1100A |
Laminating layers |
2 |
2 |
Laminating width |
800mm |
1100mm |
Unwind diameter |
600mm |
600mm |
Rewind diameter |
800mm |
800mm |
Laminating speed |
80m/min |
80m/min |
Max oven temperature |
80℃ |
80℃ |
Max heat drum temperature |
90℃ |
90℃ |
Power |
50KW |
60KW |
Weight |
6000KG |
7000KG |
Dimension |
9000*1960*2550mm |
9000*2260*2550mm |
1).Laminating layer:2 layers
2).Suitable material
BOPP 18-100μm
CPP 20-100μm
PET 12-100μm
Alu foil
Metalized film
Paper 18-60μm
PC
3).Laminating width: 800mm (800 model)
4).Material diameter: 600mm
5).Laminating speed: 5-80m/min
6).Max oven temperature: 80℃
7).Max heat drum:70-90℃.
8).Max laminating pressure: 10MPA
9).Tension draw ratio: <<1/1000
1). EPC.
2).Magnetic powder manual tension control.
3).The roll horizontal adjustment is manual
4).Air shaft
1).Max roll dia: Φ600mm
2).Roll horizontal correcting: ±60mm
3).Tension set: max 50N/m
4).Tension controlling precision: ±0.1kg
5).Max unwinding width: 800mm
6).Roll horizontal adjustment: ±20mm
1)Electric heating.
2)Waste air exhausting tunnel.
3)4 pace intelligent temperature control, material protecting roller and hot drum run synchronously.
1)Max temperature:80℃
2)Material length in the oven:75000mm
3)Blower mouth: 24 pieces
4)Max temperature controlling precision: ±2℃
5)Max intake air: 1200m³/h
6) Blower power: 1.1KW
1).EPC.
2).Magnetic powder manual tension control.
3).The roll horizontal adjustment is manual
4).Air shaft
1).Max roll dia: Φ600mm
2).Roll horizontal correcting: ±60mm
3).Tension set: max 50N/m
4).Tension controlling precision ±0.1kg
5).Max unwinding width: 800mm
6).Roll horizontal adjustment ±20mm
1)Laminating roller is hollow type.
2)The up pressing device of pressing roller is swing arm type, air pressure clamping.
1) Max temperature:80℃
2) Laminating width:800mm
3) Max temperature controlling precision: ±2℃
4) Max laminating pressure: 1500kg
5)Laminating roller: A 90°
1)Rewinding is transmitted by torque motor.
2)Rewinding air shaft
3)The horizontal adjustment of the roll is manual
1)Max roll dia: Φ800mm
2)Roll horizontal adjustment ±20mm
3)Max rewinding width 800mm
4)Tension controlling precision ±0.1kg
5)Tension set Max 40N/m
1)The wall board is made of high strength low stress combined alloy cast iron.
2)The guiding roller is hollow.
3)The main transmission adopts AC frequency control, gluing roller and hot drum adopts floating roller to control the tightness or looseness of the film.
1) Guiding roller: Φ75mm
2) Guiding roller length: 830mm
3) Frequency motor power: Gluing 1.5kw, lamination 3kw.